87.060.30 (Solvents) 标准查询与下载

ASTM D4734-07 精制苯-545的标准规范

1.1 This specification covers benzene-545.1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit in accordance with the rounding-off method in Practice E 29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 Consult current OSHA regulations, supplier's Material Safety Data Sheets, and local regulations for all materials used in this specification.

Standard Specification for Refined Benzene-545

ASTM D3735-07(2012) VMamP石油脑的标准规格

1.1 This specification covers four types of moderately volatile hydrocarbon solvents, mainly aliphatic in composition and normally petroleum distillates. These solvents are used primarily by the coatings industry and are commonly referred to as VMamp;P naphthas. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded-off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.

Standard Specification for VMamp;P Naphthas

ASTM D2693-07 乙二醇的标准规范

1.1 This specification covers ethylene glycol for use in the preparation of surface coatings.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.4 For specific hazard information and guidance, consult the supplier's Material Safety Data Sheet.

Standard Specification for Ethylene Glycol

ASTM D1617-07(2012) 溶剂和稀释剂酯化值的标准试验方法

1.1 This test method covers the determination of the ester value of solvents and thinners used in lacquers and other coatings. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see 8.6. 1.5 For hazard information and guidance, see the supplier's Material Safety Data Sheet.

Standard Test Method for Ester Value of Solvents and Thinners

ASTM D2636-07(2012) 己烯甘醇的标准规格

1.1 This specification covers hexylene glycol2 for use in paint, varnish, lacquer, and related products. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, consult supplier's Material Safety Data Sheet.

Standard Specification for Hexylene Glycol

ASTM D2627-07 双丙酮醇的标准规范

1.1 This specification covers diacetone alcohol.1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 For specific hazard information and guidance, consult the supplier's Material Safety Data Sheet.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Diacetone Alcohol

ASTM D2917-07 甲基异戊酮的标准规范

1.1 This specification covers methyl isoamyl ketone (98 % grade) for use in paint, varnish, lacquer, and related products.1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet.

Standard Specification for Methyl Isoamyl Ketone

ASTM D2635-07 甲基异丁基甲醇的标准规范

1.1 This specification covers methyl isobutyl carbinol for use in paint, varnish, lacquer, and related products.1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-had digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 For specific hazard information and guidance, consult supplier's Material Safety Data Sheet.

Standard Specification for Methyl Isobutyl Carbinol

ASTM D2693-07(2012) 乙二醇的标准规格

1.1 This specification covers ethylene glycol for use in the preparation of surface coatings. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 For specific hazard information and guidance, consult the supplier's Material Safety Data Sheet.

Standard Specification for Ethylene Glycol

ASTM D2917-07(2013) 甲基异戊酮的标准规格

1.1 This specification covers methyl isoamyl ketone (988201;% grade) for use in paint, varnish, lacquer, and related products. 1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet.

Standard Specification for Methyl Isoamyl Ketone

ASTM D2635-07(2012) 甲基异丁基甲醇的标准规格

1.1 This specification covers methyl isobutyl carbinol2 for use in paint, varnish, lacquer, and related products. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off ???to the nearest unit??? in the last right-had digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For specific hazard information and guidance, consult supplier's Material Safety Data Sheet.

Standard Specification for Methyl Isobutyl Carbinol

ASTM D2634-07 乙酸甲基戊酯标准规范(95%级)

1.1 This specification covers methyl amyl acetate (95 % grade) for use in paint, varnish, and related products.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification. 1.4 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.

Standard Specification for Methyl Amyl Acetate (95 % Grade)

ASTM D2636-07 己烯甘醇的标准规范

1.1 This specification covers hexylene glycol for use in paint, varnish, lacquer, and related products.1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 For specific hazard information and guidance, consult supplier's Material Safety Data Sheet.

Standard Specification for Hexylene Glycol

ASTM D3545-06 气相色谱法测定乙酸酯中乙醇含量和纯度的标准试验方法

1.1 This test method covers the determination by gas chromatography of the ester content and the corresponding alcohol content of acetate esters. This test method has been applied to ethyl, n-propyl, isopropyl, n-butyl, isobutyl, and 2-ethoxyethyl acetates.1.2 Water, and in some cases acetic acid, cannot be determined by this test method and must be measured by other appropriate ASTM procedures and the results used to normalize the chromatographic value.1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for material listed in this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography

ASTM D3257-06(2012) 气相色谱法测定溶剂油中芳烃的标准试验方法

1.1 These test methods cover the determination of ethylbenzene and total eight-carbon (C8) and heavier aromatics in the concentration range from 0.1 to 308201;% in mineral spirits having a distillation range from 149 to 210??C (300 to 410??F) as determined by Test Method D86. The procedures permit the identification and calculation of concentrations of aromatic components to 0.1 volume8201;%. 1.2 It is recognized by analytical chemists that a single column gas chromatography analysis of an unknown sample is risky. In such cases, multiple and different analytical techniques must be used for absolutely positive identification, for example, several different gas chromatography columns, gas chromatography/mass spectrometer, or gas chromatography/infrared, etc. In these test methods the material is known and is clearly defined. 1.3 Oxygenated compounds, if present, may interfere and cause erroneous results. Such oxygenated compounds are not normally present in mineral spirits. 1.4 Three test methods are covered as follows: 1.4.1 Test Method A, measurement of ethylbenzene content, C8 plus higher aromatics (except ethylbenzene), and total aromatics by means of a single packed column gas chromatographic analysis. 1.4.2 Test Method B, measurement of ethylbenzene content by means of a rapid packed column gas chromatographic analysis. 1.4.3 Test Method C, measurement of ethylbenzene content, C8 plus higher aromatics (except ethylbenzene) and total aromatics by means of a capillary column gas chromatographic analysis. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.

Standard Test Methods for Aromatics in Mineral Spirits by Gas Chromatography

ASTM D843-06(2011)e1 硝化级二甲苯的标准规范

1.1 This specification covers nitration grade xylene. 1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be round off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the round-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 Consult OSHA regulations, supplier's Material Safety Data Sheets, and local regulations for all materials used in this specification.

Standard Specification for Nitration Grade Xylene

ASTM D3540-06 合成乙酸伯戊酯(98%级)

1.1 This specification covers synthetic primary amyl acetate (98 % grade).1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for material listed in this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Primary Amyl Acetate, Synthetic (98 % Grade)

ASTM D1613-06(2012) 色漆、清漆、喷漆和有关产品用挥发性溶剂和化学介质中酸度的标准试验方法

1.1 This test method covers the determination of total acidity as acetic acid, in concentrations below 0.058201;%, in organic compounds and hydrocarbon mixtures used in paint, varnish, and lacquer solvents and diluents. It is known to be applicable to such mixtures as low molecular weight saturated and unsaturated alcohols, ketones, ethers, esters, hydrocarbon diluents, naphtha, and other light distillate petroleum fractions. 1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 For specific hazard information and guidance consult supplier's Material Safety Data Sheet. 1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products

ASTM D3545-06(2012) 气相色谱法测定乙酸乙酯中乙醇含量和纯度的标准试验方法

1.1 This test method covers the determination by gas chromatography of the ester content and the corresponding alcohol content of acetate esters. This test method has been applied to ethyl, n-propyl, isopropyl, n-butyl, isobutyl, and 2-ethoxyethyl acetates. 1.2 Water, and in some cases acetic acid, cannot be determined by this test method and must be measured by other appropriate ASTM procedures and the results used to normalize the chromatographic value. 1.3 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off ???to the nearest unit??? in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for material listed in this specification. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Alcohol Content and Purity of Acetate Esters by Gas Chromatography

ASTM D1613-06 色漆、清漆、喷漆和有关产品用挥发性溶剂和化学介质中酸度的标准试验方法

This test method is useful for determining low levels of acidity, below 0.05 %, in organic compounds and hydrocarbon mixtures. The total acidity is calculated as acetic acid or milligrams of sodium hydroxide per gram of sample. Acidity may be present as a result of contamination, decomposition during storage or distribution, or manufacture. This test method may be used in assessing compliance with a specification.1.1 This test method covers the determination of total acidity as acetic acid, in concentrations below 0.05 %, in organic compounds and hydrocarbon mixtures used in paint, varnish, and lacquer solvents and diluents. It is known to be applicable to such mixtures as low molecular weight saturated and unsaturated alcohols, ketones, ethers, esters, hydrocarbon diluents, naphtha, and other light distillate petroleum fractions.1.2 For purposes of determining conformance of an observed value or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 For specific hazard information and guidance consult supplier's Material Safety Data Sheet.This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products